Quick dry electronic cleaning solvent.
CRC QD-Contact Cleaner is a stable, inert, high-purity solvent cleaner, formulated for applications where
lower flash point solvents may be used, and where sensitive plastics are involved. Based on very fast drying,
hydrocarbon solvents without CFC’s, HCFC’s, chlorinated-, fluorinated-, alcohol- or glycol ether
components. CRC QD-Contact Cleaner provides a suitable precision cleaning action for sensitive
electronics and electrical equipment without risk of costly damage.
2.Features
• Quick drying.
• Effectively removes light contaminants, dust, dirt, finger prints, traces of light oil and moisture.
• No ozone-depleting action (ODP = 0,00).
• Reduces contact resistance, arcing and wear.
• Extends the life of sensitive equipment.
• Non-conductive and non-corrosive.
• Leaves no residue.
• Safe on commonly used plastics, rubbers and coatings.
• Convenient 360° (upside-down) spray valve for aerosols.
• High purity CO2 propellant, giving an active product content of 95 %
• Spray liberally on surface to be cleaned and allow to run off. Use extension tube for precision
application.
• Use an abrasive on surfaces with carbon deposits or oxidation; remove residue with intermittent
spray. Re-lubricate with CRC 2-26 if necessary.
• Highly flammable formulation. Do not spray on energized electrical equipment or circuits; de-activate
before product application and extinguish all flames, pilot lights and heaters
• During use, flammable vapours may accumulate, especially in closed equipment. Use with adequate
ventilation and maintain ventilation until vapours are gone. Allow to dry thoroughly before reactivating
systems.
• Observe care in applications on highly sensitive plastics, adhesive-mounted or stressed parts.
Maintains and protects all electrical
equipment. Displaces and seals out water
and moisture. Prevents corrosion and
oxidation. Penetrates and lubricates.
2. Features
• Multi purpose fluid.
• Does not contain silicones.
• Protects metals and alloys.
• Displaces and seals out water and moisture.
• Loosens metal parts seized by dirt, corrosion or dried-up grease.
• Penetrates quickly.
• Safe on all metal surfaces, does not stain.
• Safe on most rubbers, plastics and coatings. Test on sensitive or stressed materials before use.
• Convenient 360° (including inverted position) spray valve for aerosols.
• High purity CO2 propellant, giving an active product content of 95%
Quick drying, colourless transparent insulating and protective coating based on acrylic
resins.
2. FEATURES
• PLASTIK 70 is a low viscosity, solvent drying acrylic based conformal coating with
excellent insulating properties. The lacquer is colourless transparent and elastic. It has a
durable adhesion in the temperature range from –40°C to +60°C and can be used for a
short period of time up to +100°C maximum. It protects printed circuit boards and
surfaces from humid anorganic-acid or caustic vapours.
• PLASTIK 70 is colourless-transparent and as such is not visual on the printed circuit
board surface.
• For repair works PLASTIK 70 can be soldered through or be totally removed with aceton,
THINNER FOR PLASTIK 70.
Lack of effective contact maintenance can affect relay panels in thermal power plants, affect the performance of signalling systems in railways, and cause pollution flashovers in high voltage insulators. Kli-nit Contact Cleaner removes oxidation, oil, and other contaminants of metal switches, motors, relays, generators, edge connectors, buss bars, circuit breakers, scales and sensors. Especially formulated to clean electrical equipment controls, ignition systems, motors, relays and thermostats, kli-nit contact cleaner will remove oil and grease and even moisture and dust particles that may be covering and impairing the contact points of electrical equipment.
BE 100% SURE
3
kli-nit CT-2 is not a lubricant and does not contain oils or other lubricants.
CT-2 NTACT CLEANER
Complies with MIL spec MIL-PRF 29608A
– Highly non-polar organic solvents for cleaning efficiency
– Dries quickly
-Does not contain oil or other harmful substances
-Complies with international packaging standards
Is environment friendly
-Thousands of satisfied customers & many performance certificates
APPLICATIONS:
1 Railway- for cleaning of Interlock of all relays and BL limit switches of AC electric locos.
2. Power Plants- ELECTRICAL & ELECTRONIC CONTACTS, MOTORS, BREAKERS, ETC
2. printed circuit boards, electrical signals., controls, switches, precision instruments and electric panels
3. Airforce- Radars, communication systems, Information technology.
4. Used in electrical and electronic switchgear, equipment & components, electrical and electronic contacts, high pressure discharged equipment.
Graphite lacquer for conductive coatings. Thermoplastic binder with electrically conductive
graphite powder.
2. FEATURES
• GRAPHIT 33 contains a high level of pure and fine graphite powder. This results in a good
electrical conductivity, as well as gliding and release agent properties of the graphite
lacquer. The coating exhibits good adhesion on metal, many plastics, glass and wood.
Gazolin Are A Industry & Manufacturing Services Provider Institutions. Suitable For Factory, Manufacturing, Industry, Engineering, Construction And Any Related Industry Care Field.
